Your Modular Building Source (sm)

Visa/MC

Ships in 48 Hours !

Need a fast Guard Shack!!!

4' x 4' Guard building $3495.00 or 4' x 6' $3996.00

Ships in 48 Hours !

Each Unit has Standard
(1) 110 V Outlet, (1) Light, (1) Shelf, and Breaker Box

Quote and Floor Plan Detail Drawings (pdf) Free Down Loads

4' x 4' Guard building

4' x 6' Guard building

Options

230V HVAC / 11,600 C / 11,600 H BTU

with 1 each HVAC unit, framed cutout (in wall panel)

$1027.00

Purchase Orders

Offices are shipped LTL or truck load. Payment may be freight collect due on delivery or billed to the users freight account. We also offer per pay and add. Modular Office pays the freight and bills the user cost of the freight plus 10%. Unless otherwise noted, the prices quoted do not include off loading, building installation, electrical hook-up, climate control installation, permits, engineering calculations, or architectural-type drawings.

PART 1 – GENERAL

1.1 Provide all labor, equipment and materials to furnish and install prefabricated portable anodized aluminum building's) where shown on the drawings.

1.2 Related work Specified Elsewhere.

1.2.1 Electrical service supply and connection.

1.2.2 Site/Foundation work.

1.2.3 Unloading, placement, installation and anchoring.

1.2.4 Plumbing and piping (when required).

1.3 Quality Assurance

1.3.1 Structures shall be the product of a manufacturer with a minimum of 30 years-documented experience in the design and fabrication of portable aluminum buildings.

1.3.2 The approved sales company is Modular-Office.com

1.3.3 Prefabricated buildings by manufacturers other than the one approved shall submit sufficient data to enable approval to be given. As a minimum: Design drawings and /or calculations, applicable certifications, catalog information, and color samples showing equal range of variety.

1.3.4 Electrical devices factory installed within the prefabricated building shall be UL listed. Factory installed wiring system shall bear UL Classification insignia certifying compliance with the National Electrical Code, 1990 & 1993 editions.

1.3.5 Adherence to applicable portions of state and local building codes is the responsibility of the owner. Building manufacturer shall not be responsible for permits, special engineering calculations, or architectural type drawings unless otherwise notified in writing 3-weeks prior to release of bid document.

1.3.6 Design Loads: 50 PSF live load, 30 PSF wind load.

1.5 Submittals

1.5.1 Upon award of order, manufacturer shall prepare and submit copies of shop drawings as required for each different building required for this project. Drawings shall include elevations, section, floor plan, electric schedule, service entrance locations, and anchor clip detail.

PART 2 – PRODUCTS

2.1 Product Construction

Building to be of aluminum construction, with natural satin anodized aluminum framework. Building height to be 88 1/8” including rimfit exterior roof.

2.1.1 Structural members to be extruded aluminum angles, channels, and tee sections of structural alloy 6063T6, anodized 204R1, with ribbed pattern exterior surfaces.

2.1.2 Fasteners used to manufacture and assemble buildings to be corrosion-proof type and to permit on-site replacement of damaged components. Welded fabrication is not acceptable.

2.2 Wall and Ceiling Panels

2.2.1 Wall panels to be ¾” high-impact resistant and expansion resistant insulating OSB. Ceiling panel to be ¾” thick, high impact resistant, moisture resistant, and expansion resistant insulating OSB with white vinyl permanently laminated to interior side, and plastic protective sheet laminated to upside.

2.3 Finish

Stucco embossed, mill finished aluminum sheet permanently laminated to exterior side.

2.4 Floor Structure

Floor structure to be an integral part of the building with 1 ½” solid waterproof insulating core fit tight against panels and fastened to bottom structural base frame.

2.4.1 Finished floor shall be 3003 Treadbrite safety treadplate floor covering.

2.5 Doors

Doors to be ¾” thick, bottom-track, patio type sliding door and half-glazed. Bottom portion to include panel finish to match interior and exterior building walls.

2.5.1 Provide 2 bottom track sliding doors (one on each side).

2.6 Windows and Glazing

Windows shall have anodized aluminum frames and inserts and to be industrial quality with active

window panel to slide horizontally on stainless steel, ball-bearing rollers (plastic rollers are not

acceptable). Windows to include inside positive locking device. Exterior window sill height to be

38” (inside sill height 34” from finished floor).

2.6.1 Windows to be glazed with 3/16” clear tempered safety glass.

2.7 Counter

Furnish 22” deep, plastic laminate counter, walnut woodgrain, 32” a.f.f.

2.8 Electrical

Electrical service to include singe phase, 100 amp capacity load center, pre-wired in conduit, with one 230v circuit and four 115v circuit capacity – provide two spare circuits. All electric work shall be in compliance with the National Electrical Code. All electrical components shall bear the UL label.

2.8.1 Furnish one 115v duplex outlet, and one 230v single outlet.

2.8.2 Lights to be fluorescent type fixture with acrylic lens (tubes to be furnished by others) and pull chain.

2.9 Exterior Roof

Exterior waterproof roofs include ribbed anodized fascia trim, matching structural with integral, self-contained gutters. Provide a 3” overhang. Roof ships installed.

PART 3 – EXECUTION

3.1 General

Install prefabricated buildings on a flat and level concrete pad in accordance with the manufacturer’s placement drawings. Position units over the utility stub-ups; verify building is level and anchor (Anchors are supplied on site, by others. Comply with local codes).

CChanging Space, McGill & Company, Modular-Office.com, Modular Office, Modularoffice, ModularDirect.com, ModularDirect.net, ModularDirect.org, and Modular Direct are Trade Marks and or Service Marks of McGill & Company.